How to make a portrait tattoo stencil from a photo
Portraits are where stencils make or break the piece. A few millimetres of drift in the eyes or mouth and it stops looking like the person. The goal is a stencil that locks down proportions and shadow shapes while leaving the shading to you.
Updated 17 November 2026
Start with the right reference
No setting rescues a poor reference. Before you open any tool, check the photo against this list, and ask the client for alternatives if it fails more than one point.
- Resolution. The face should be at least 600–800 pixels tall in the photo. Screenshots from social media and messaging apps are often compressed far below that.
- Focus. Zoom in on the eyes. If the eyelashes are a blur, the stencil will be too.
- Directional light. Light from one side, slightly above, makes clear shadow shapes on the nose, cheek and jaw. Flat front light (on-camera flash) gives a face with no shapes to trace.
- Pose. Three-quarter views usually tattoo better than straight-on. Avoid extreme angles, wide-angle phone distortion close to the face, and hands covering the face.
- Nothing crossing the face. Hair strands, glasses reflections and shadows from hats create lines you will spend time removing.
Prepare the photo
- Crop to the subject. Head and shoulders, or whatever the tattoo will include. Less image means less noise.
- Adjust contrast if the photo is flat. A small boost in your phone's photo editor makes shadow edges easier to detect. Do not push it until skin turns white; that erases the soft forms you need.
- Remove the background. A busy background produces lines that touch the hair and shoulders and are slow to separate. In StencilReady, remove plain background handles flat or near-flat backgrounds. For a cluttered scene, cut the subject out with your phone's photo editor first, then load the cutout.
- Convert to black and white only if colour confuses the edges. Red lips on pale skin can show strong or weak edges depending on the tool. Try both versions.
Which lines to keep
A realism stencil is not a drawing of the photo. It is a set of markers that tell you where things are. Keep:
- The outer contour: jawline, ear, hairline, neck and shoulder edge.
- Features: eye shapes, the iris circle and highlight, nostrils, the line between the lips, the edges of the lips.
- Shadow boundaries: where a large shadow starts, for example the shadow side of the nose, under the cheekbone, under the jaw. These lines carry the likeness more than any feature.
- Major hair masses: the outline of the hair and the main parting or flow, not individual strands.
Leave out:
- Skin texture, pores, freckles and fine wrinkles (you shade these).
- Individual hairs and eyelashes, apart from a few guide strokes.
- Fabric texture and small clothing folds.
- Gradients. A soft gradient has no edge and produces scattered dots.
Some artists add a light dotted or dashed line for soft shadow edges and keep solid lines for hard edges. If you do, draw those by hand after generating the main stencil, so you control where they go.
Settings for portraits in StencilReady
- Style: Sketch. It keeps natural line weight, so the strong edges (eyes, jaw, deep shadow) come out heavier and the soft ones lighter. That variation helps you read the stencil while working. Use Outline if you prefer even lines for touch-up.
- Detail: start in the middle and go down. On a portrait 10–15 cm tall, moderate detail keeps the features and shadow shapes. Lower it for smaller pieces.
- Sensitivity: lower than for flash. Higher sensitivity picks up faint edges in the skin, which is mostly noise in a portrait.
- Line weight: 0.3–0.4 mm. Realism is usually lined, if at all, with 3RL or smaller, so the stencil should sit under fine work. Do not go below 0.3 mm on a 203 dpi printer. See line weight and needle size.
- Clean up stray marks: on. Removes isolated specks from skin texture.
- Smooth: low to moderate. Too much smoothing rounds off the corners of the eyes and mouth, which are exactly where likeness lives.
- Fill darks: off unless the piece is high-contrast blackwork. On a realism portrait, solid fills cover areas you need to see while shading.
Pro's Realism outline preset sets the style, detail, sensitivity and weight in one step as a starting point.
Size matters more for portraits
Faces need room. Below about 7–8 cm for the face itself, the space between features gets too small to hold detail as the tattoo ages, and the stencil will look cramped. If the client wants a small portrait, simplify: fewer shadow lines, bigger shapes, lower detail. Set the size from a measurement of the placement and print at 100%; see printing at actual size.
Check the stencil before printing
- Switch to the violet on skin preview and look at it at arm's length. Can you recognise the person from the stencil alone? If not, the shadow boundaries are missing.
- Compare eye spacing and the eye-to-mouth distance with the reference. These carry the likeness.
- Look for doubled lines along strong edges and stray lines in the hair. Lower detail or remove them in a touch-up pass (see the hybrid workflow).
Then print, apply and keep the full reference on a screen next to you. The stencil gives you the map; the photo gives you the values. The full process is in how to make a tattoo stencil.