How to print a tattoo stencil at actual size
You measured 12 cm on the client's forearm. The stencil comes out 11.3 cm. Nothing is wrong with the design: something between the file and the paper scaled it. Here is where that happens and how to make every print come out at the exact size.
Updated 17 November 2026
Why stencils print at the wrong size
A stencil has a physical size only if three things agree: the file says how big it is, the print dialog does not rescale it, and the printer does not rescale it either. Most size errors come from one of these:
- “Fit to page” or “Shrink to fit”. The print dialog shrinks the page so it fits inside the printer's printable area. Because every printer has a margin it cannot print into, the shrink is almost always 3–8%. On a 12 cm design that is 4–10 mm, which is enough to throw off lettering or a piece that has to line up with an existing tattoo.
- Paper size mismatch. An A4 page printed on US Letter paper (or the reverse) gets scaled to fit. A4 is 297 mm tall, Letter is 279.4 mm, so an A4 layout squeezed onto Letter comes out at about 94%.
- Image with no real size. A PNG or screenshot carries pixels, not centimetres. Printing it from a photo app stretches it to whatever the app thinks looks good. The size is a guess.
- Phone printing apps. Many printer companion apps scale images to the paper width by default. Look for a “Original size” or “100%” option, or print from a PDF instead.
Set the size before you print
Measure the placement on the client first, then set the design's width or height to that measurement. In StencilReady you enter the size in centimetres or inches and the preview shows rulers on the sheet edge, so the screen matches the paper. Pick the paper you actually have loaded: A4, US Letter or US Legal. Legal (8.5 × 14 in) is handy for long forearm and calf pieces.
If the design is bigger than the sheet, Pro splits it across several sheets with overlap and alignment marks, so you can tape them together into one stencil for a back piece or thigh.
Print dialog settings that keep the size
The names change between browsers and systems, but the setting you want is always “do not scale”.
| Where you print from | Setting to use | Setting to avoid |
|---|---|---|
| Chrome or Edge print dialog | Scale: Default or Custom 100; margins: Default | “Fit to printable area”, custom scale other than 100 |
| Safari / macOS print dialog | Scale 100% | “Scale to fit” |
| Firefox | Scale 100% | “Fit to page width” |
| Adobe Acrobat Reader | Page sizing: “Actual size” | “Fit” and “Shrink oversized pages” |
| macOS Preview | Scale 100% | “Scale to fit” |
| Windows printer driver | Paper size matching the loaded paper | Any “fit to paper” or zoom option |
If you print from a phone or tablet, download the PDF and print the PDF. PDFs carry a fixed page size, so a correctly set up print path has nothing to guess. Printing an image directly from the photo gallery almost always rescales it.
Check the size with the calibration ruler
Every StencilReady sheet includes a calibration ruler in centimetres or inches, depending on the unit you chose. Before you cut the stencil out, measure it with a real ruler.
- Lay a steel or plastic ruler along the printed ruler, zero to zero.
- Check the full length, not just the first mark. A 3% error is under 0.3 mm over 1 cm, which you cannot see, but it is 3 mm over 10 cm.
- If the printed ruler matches, the design is the right size. If it is short, something scaled the page; go back to the print dialog.
Do this once per printer and per device you print from. After the first good print, the same settings keep working until a driver update or a new device changes them.
Fixing a print that is consistently off
If you have checked every scale setting and the ruler is still short or long by the same amount:
- Check the paper size in the printer driver, not only in the browser. A driver set to Letter with A4 loaded will rescale or crop.
- Check the printer's own settings. Some portable thermal printers have a “fit to paper” or “auto scale” option in their app or utility that applies to every job.
- Check the dpi. A driver set to 203 dpi on a 300 dpi printer (or the reverse) can print at the wrong size when an app sends raw pixels. Printing from the PDF avoids this.
- Measure the paper. Some cheap thermal paper is cut slightly off size. That does not change the design size, but it can make a driver think the paper is something else.
If the error stays the same after all that (for example the 5 cm ruler always measures 49 mm), let StencilReady correct it. In the editor, open Output → Prints the wrong size? and type what the ruler measured. Every PDF after that is scaled by the difference (here +2%) on that device, so the next print comes out at true size.
Size on screen vs size on skin
Screens lie about size: the same design looks different on a phone and a monitor, and pinch-zoom makes it meaningless. Show the client the printed stencil held against the placement, or the stencil applied, before you commit. Skin also stretches: a stencil applied to a flexed forearm will look narrower when the arm relaxes. Apply with the body in the position it will usually be in.
Quick checklist
- Measure the placement and set the size in cm or inches.
- Choose the paper size you have loaded.
- Print the PDF at 100% / “Actual size”. Never “Fit to page”.
- Leave mirror off for thermal printers and copiers.
- Measure the calibration ruler over its full length before cutting.
Next: thermal printer stencil settings for density, paper loading and line thickness, or troubleshooting a stencil that will not transfer.