Thermal printer stencil settings
Most stencil problems that look like printer faults are settings: density too high or too low, the wrong side of the paper facing the head, lines thinner than the printer can render, or a mirror switch flipped the wrong way. This guide covers the settings that matter for the three common setups.
Updated 17 November 2026
How thermal stencil paper works
Thermal stencil paper has four layers: a white top sheet, a yellow tissue interleaf, a purple carbon sheet, and the stub that holds them together at the top. The tissue only protects the carbon during storage. The printer head heats the white sheet where there is a line, and the heat melts carbon from the carbon sheet onto the underside of the white sheet. That violet carbon is what transfers to skin.
Before printing, tear or fold away the yellow tissue so the carbon sheet touches the white sheet directly. Leave the stub attached so the sheets stay aligned.
Mirror or not?
This is the most common question, and the answer depends on how the image gets onto the skin.
| Method | Mirror? | Why |
|---|---|---|
| Thermal printer (PocketJet, Phomemo-type, others) | No | The carbon lands on the back of the white sheet as a mirror image. Pressing that back onto skin flips it again, so the skin reads correctly. |
| Thermal copier | No | Same carbon process as a thermal printer. |
| Hand tracing on thermal paper with a pen | No | You draw on the white sheet's front; the carbon copies onto its back, same as the printer. |
| Hectograph pencil or stencil pen on tracing paper | Yes | You draw on the side that touches skin, so the skin gets a mirror of your drawing. Mirror the design first, or trace it from the back. |
| Inkjet printer with stencil ink | Yes | The printed side is pressed straight onto skin. |
Lettering is the quick test: if text on your print reads normally and you use a thermal printer, it will read normally on skin. StencilReady keeps mirror off by default; turn it on only for the methods marked “Yes”.
Resolution: match the printer's dpi
Thermal heads have a fixed resolution. Sending an image at the printer's native dpi means one image pixel equals one dot on the head, so lines stay crisp instead of being resampled.
- Brother PocketJet (PJ-7 and PJ-8 series): 300 dpi.
- Phomemo and similar A4 portable thermal printers: usually 203 dpi; some newer models are 300 dpi. Check the spec sheet of your model.
- Thermal copiers: you feed a printed copy of the stencil, so the copy only needs to be sharp and black. Print it at 300 dpi on a laser or inkjet printer.
In StencilReady, pick your printer under Output → Printer (300 dpi thermal, 203 dpi portable thermal, or inkjet/laser). The free version exports at 150 dpi, which prints cleanly at normal stencil line weights. Pro exports at the printer's native resolution, 300 or 203 dpi, so one pixel lands on one dot.
The stencil must be pure black on white, with no grey. Grey pixels turn into dotted, speckled lines on a thermal head because the head can only heat a dot or not. Stencils from StencilReady are pure black and white by design.
Density (darkness)
Density controls how much heat the head applies. More heat means darker, wider lines; too much heat spreads the carbon and makes thin lines blob together.
- Brother PocketJet: start at density 6 or 7 in the printer driver or settings utility. Go up one step if lines print faint, down one if fine detail fills in.
- Phomemo-type printers: the companion app or driver has a darkness or concentration slider. Start in the middle and raise it until the lines are solid on the first try, not after a second pass.
- Thermal copiers: use the depth or darkness dial. Start in the middle; a faint original needs more depth, a very dark one less.
Change one step at a time and print a test strip of the same design. Low-quality or old paper often needs one step more heat than fresh paper.
Line thickness the printer can render
A line has to cover at least two or three dots on the head to print as a solid line. That works out to a practical minimum of about 0.3 mm:
- At 203 dpi, one dot is 0.125 mm, so 0.3 mm is about 2.4 dots.
- At 300 dpi, one dot is 0.085 mm, so 0.3 mm is about 3.5 dots.
Lines thinner than this break up, especially on curves and diagonals. For most work, 0.4–0.6 mm stencil lines are a safe default. If you need fine-line detail, keep the outline at 0.4 mm or more and use 0.3 mm only for interior lines. See line weight and needle size for how to pick a weight.
StencilReady warns you under the line weight slider when the weight you chose is below what your selected printer can print solid.
Loading the paper
- Remove the yellow tissue. Keep the white sheet and carbon sheet together at the stub.
- Feed the stub (joined) end first, so the sheets cannot shift apart as they pass the head.
- Face the white sheet toward the print head. Printer designs differ, so check your manual or the arrow on the paper guide; if a sheet comes out blank, flip it for the next one.
- Keep the sheet straight against the guide. A skewed feed gives a stretched or wavy stencil.
Margins
Most portable thermal printers cannot print in a band of about 4–6 mm along the edges. Keep the design inside the printable area, and leave a few millimetres of paper around it so you can trim the stencil. StencilReady lays the page out for A4, US Letter or US Legal at true size; set your print dialog to 100% as described in printing at actual size.
Quick fixes
| Problem | First thing to try |
|---|---|
| Blank sheet | Paper upside down; flip it so the white sheet faces the head. |
| Faint lines | Raise density one step; check the tissue was removed. |
| Thin lines broken | Increase line weight to 0.4 mm or more; export at the printer's dpi. |
| Fine detail fills in | Lower density one step; reduce detail in the stencil. |
| Lettering backwards on skin | Mirror was on; turn it off for thermal printers. |
| Wrong size | Print at 100%, not “Fit to page”. |
For problems after the stencil is on skin, see stencil not transferring. To make a stencil to test these settings with, open the stencil maker.